WA & OR · GUIDE

Seasoning firewood in the Pacific Northwest: how long it takes

Seasoning firewood takes about 6 to 12 months: at least six months for softwoods such as Douglas fir and a year or more for hardwoods such as maple, alder and oak. West of the Cascades, split and stack by spring so the wood dries through July and August, the only months Seattle and Portland average under an inch of rain, and keep the top covered all winter.

Researched by Westcoast-Tree.org · Checked 2026-10-02 · Sources at the end

Short answer

Seasoning firewood takes about 6 to 12 months, until it reads below 20% moisture. Washington’s Department of Ecology says softwoods such as Douglas fir need at least six months and hardwoods such as maple and oak a year or more. West of the Cascades, split and stack by spring, dry it through July and August, keep the top covered all winter and check it with a moisture meter.

How long does seasoning firewood take?

Plan on 6 to 12 months from splitting to burning. The range depends on the species, the size of the splits, how the stack is built and the weather. Oregon’s Department of Environmental Quality (DEQ) puts the process at about 6 to 12 months, the EPA’s minimum is six months, and Washington’s Department of Ecology splits it by wood type: at least six months for softwoods, a year or more for hardwoods.

SourceHow longWhat else it says
EPA Burn WiseAt least 6 monthsWood burns best below 20% moisture
Oregon DEQAbout 6–12 monthsBuy next winter’s wood well ahead; split to about 3½–6 inches
Washington Ecology (2025)Softwoods 6+ months; hardwoods a year or moreSplit, stack, cover, store; check with a meter
Washington Ecology, wood stove pageAt least 1 yearWood split, covered and stacked
OSU Extension EC 1387Generally 6–8 months; hardwoods longerCut by late winter or early spring
OSU Extension EC 1628 (western Oregon)Through one dry summer; two is betterKeep it dry through the rainy season

Sources: EPA Burn Wise; Oregon DEQ; Washington Department of Ecology; OSU Extension EC 1387 and EC 1628. All checked 2026-10-02.

The Northwest twist is timing. A cord split in October has six months ahead of it, but they are the wettest six months of the year: October through March brings 75 percent of Seattle’s yearly precipitation. That is why OSU Extension tells western Oregon wood burners to season through a dry summer, and why its older bulletin says to cut by late winter or early spring.

Cut trunk sections of a felled tree lying in a row on grass beside a fresh stump, with a wall and mature trees behind
Rounds like these are the start, not the finish: Oregon DEQ says wood split to about 3½ to 6 inches across dries faster. Photo: Pinecrest Tree Services / Unsplash

Why Northwest firewood dries in summer: rain west and east

NOAA’s 1991–2020 climate normals show the pattern. Seattle-Tacoma averages 39.34 inches of precipitation a year, but July and August together bring only 1.57 inches, while November alone brings 6.31. Portland follows the same curve: 1.05 inches in July and August, and 74 percent of its 36.92 inches from October through March.

Seattle precipitation by month (inches) NOAA 1991–2020 normals, Seattle-Tacoma International Airport. July, the driest month, is highlighted; June to September is the drying window.
Source: NOAA NCEI 1991–2020 monthly normals, station USW00024233, checked 2026-10-02.

East of the Cascades a woodpile gets far less precipitation. Yakima averages 8.01 inches a year, about a fifth of Seattle’s, and 10 of its 12 months average under an inch; Kennewick matches that, and Bend has nine such months. Spokane is wetter at 16.45 inches, plus about 45 inches of snow.

Yearly precipitation, west vs east of the Cascades Inches per year, NOAA 1991–2020 normals; east-side cities marked
  • Olympia50.62
  • Eugene40.83
  • Tacoma40.81
  • Salem40.08
  • Seattle39.34
  • Portland36.92
  • Bellingham34.71
  • Medford18.43
  • Spokane east side16.45
  • Bend east side10.62
  • Yakima east side8.01
  • Kennewick east side7.87
Source: NOAA NCEI U.S. Climate Normals, 1991–2020, nearest airport or city station, checked 2026-10-02.
CitySide of CascadesYear (in)July + August (in)October–March (in)Share in October–MarchMonths under 1 inch
SeattleWest39.341.5729.6575%2
OlympiaWest50.621.4939.7078%2
PortlandWest36.921.0527.3274%2
SalemWest40.080.6431.3678%2
EugeneWest40.830.7131.7278%2
MedfordWest18.430.5713.8575%4
BendEast10.620.797.0867%9
YakimaEast8.010.415.5870%10
SpokaneEast16.450.8911.0167%3
KennewickEast7.870.385.2066%10

Source: NOAA NCEI 1991–2020 monthly normals (stations USW00024233, USW00024227, USW00024229, USW00024232, USW00024221, USW00024225, USC00350694, USW00024243, USW00024157, USC00454154), checked 2026-10-02. Sums computed from monthly values.

So a roof matters most on the west side. A stack in Olympia sits through about 39.7 inches of precipitation between October and March; one in Yakima sees 5.58. Medford, west of the crest but in the dry Rogue Valley, falls in between with 18.43 inches a year. For how your area’s winters compare, see Washington and Oregon hardiness zones.

The same calendar applies to a tree you are taking down: felled and bucked in late winter or spring, its wood gets the whole dry season. What the job involves is on tree removal.

Have a dead or unwanted tree?

Fell and split it in spring, and the wood can be dry by fall. Have the tree’s height and your city ready when you call.

Call for a local estimate(877) 720-7431

Which firewood seasons fastest? Green moisture by species

Species sets the starting line. The USDA Forest Service’s Forest Inventory and Analysis (FIA) tables put the green moisture of Douglas fir at 35 percent of its dry weight, against 71 percent for bigleaf maple, 99 percent for red alder and 138 percent for black cottonwood.

Water in fresh-cut wood, by species Green moisture content, percent of oven-dry weight; conifers marked
  • Black cottonwood138%
  • Quaking aspen129%
  • Red alder99%
  • Ponderosa pine conifer90%
  • Paper birch74%
  • Bigleaf maple71%
  • Pacific madrone66%
  • Oregon white oak58%
  • Western hemlock conifer56%
  • Western redcedar conifer40%
  • Douglas-fir conifer35%
Source: USDA Forest Service FIA reference tables (REF_SPECIES, MC_PCT_GREEN_WOOD), checked 2026-10-02.

More water means more to lose. In this site’s model, a cord of Douglas fir sheds about 370 pounds of water on its way to 20 percent, red alder about 1,560 and black cottonwood about 1,940; the species-by-species numbers are in how much a cord of wood weighs. The softwood-versus-hardwood rule is a starting point, not a law: ponderosa pine starts wetter than Oregon white oak, and alder and cottonwood start wetter than both.

How to stack and store firewood so it dries

  1. Split it earlyOregon DEQ says wood dries faster and burns best split to about 3½ to 6 inches in diameter. OSU Extension’s EC 1387 says to cut by late winter or early spring so the wood gets the summer.
  2. Get it off the groundDEQ says at least 6 inches up. Pallets, poles or concrete blocks all work, per EC 1387.
  3. Stack for airflowDEQ suggests stacking loosely in alternating layers, and EC 1387 says crossing the wood log-cabin style promotes good airflow.
  4. Cover the top onlyThe EPA says to store wood outdoors with only the top covered, because covering the sides traps moisture. OSU’s Ask Extension answer says the same: cover the top, leave the sides to the wind.
  5. Keep it in the openStack where air reaches every side, not tight against a wall. In wildfire country, where the pile sits is also part of your defensible space.
  6. Bring in a few days at a timeOSU Extension notes that rain on summer-dried wood dries off within a day or two once the wood is inside near the stove.
A woodpile built to dry: raised base, covered top, open sides, gap from the wall Split firewood stacked in a row on a raised base at least 6 inches off the ground, with crisscrossed ends holding the stack, a cover over the top only, open sides that let air move through, and an air gap between the stack and the house wall. Wall Air gap Cover the top only Crisscrossed ends Sides open, air moves through Raised at least 6 in off the ground Pallets, poles or blocks under the stack
A stack built to dry: raised base, crisscrossed ends, cover on top only, open sides and room between the stack and the wall. Based on Oregon DEQ, EPA Burn Wise and OSU Extension guidance.

How to use a firewood moisture meter

A meter takes the guessing out of it. The EPA’s moisture-meter flyer gives the method: split a piece, push the probes into the newly split side, and read it, following your meter’s instructions; dry wood reads below 20 percent. Test pieces from the middle of the stack as well as the edges before you call the whole pile ready.

  • Look: the EPA says seasoned wood is darker than fresh wood.
  • Lift: it weighs less. OSU’s EC 1387 suggests weighing the same pieces once a month; two months in a row with no weight loss means the wood is ready.
  • Listen: knock two pieces together. EC 1387 says dry wood makes a sharp crack and wet wood a dull thud; the EPA describes a hollow sound.
  • Measure: a meter reading below 20 percent on a freshly split face settles it.

Why it matters: the EPA’s flyer warns that wet wood gives less heat and more smoke and creosote, and OSU Extension’s EC 1628 says each 1 percent of extra moisture costs about 1 percent of heating value.

Kiln-dried vs seasoned firewood

Seasoned firewood is air-dried in a stack. Kiln-dried wood is dried with heat in a chamber; in Forest Products Laboratory trials, kilns first brought firewood to a pest-killing core temperature and then kept drying it until moisture fell to 20 percent or below.

Drying and pest treatment are separate claims. The Forest Products Laboratory describes heat treatment as an approved method to kill emerald ash borer in firewood, and USDA’s T314-A schedule, one of the standards the National Plant Board lists, holds the wood core at 60°C (140°F) for 60 minutes. Washington’s import rule (chapter 16-476 WAC, in effect since August 18, 2026) asks more: firewood from outside the state must reach a core of 71°C (160°F) for at least 60 minutes and carry an “Approved Pest Free” label with its source, or be USDA-certified packaged firewood. Air-drying does not qualify.

So a bag that only says “kiln-dried” tells you about moisture, not pests. In Washington, look for that label on any firewood brought from out of state; why it matters is on emerald ash borer in Washington, and how much wood you are buying is in how much is a cord of firewood.

Burn bans and wet-wood smoke rules in Washington and Oregon

Wet wood is more than wasted heat in Washington. WAC 173-433-110 bars smoke above 20 percent opacity from a wood stove or other solid fuel device for six consecutive minutes in any hour, apart from up to 20 minutes in any four hours when starting a new fire, and Ecology tells stove owners to burn wood that has been split, covered and stacked for at least a year.

Washington burn bans

Stage 1: no uncertified wood stoves or fireplaces. Stage 2: no wood stoves at all. Homes where the stove is the only source of heat are exempt.

WAC 173-433-150; Ecology says to check the Washington Air Quality Map or your local clean air agency · Checked 2026-10-02. Ecology burn bans

In Oregon, curtailment is local. Multnomah County posts a yellow or red day by 11 a.m., running noon to noon; on a red day, wood and pellet stoves, fireplaces, fire pits and chimineas are off limits. Households can apply for an exemption, for example when wood is the only heat source or household income is at or below 60 percent of Oregon’s median, and exemptions expire every September 30.

Lane County (LRAPA)

Red advisory: no visible smoke from wood stoves, pellet stoves or fireplaces inside Eugene, Springfield and Oakridge city limits and their urban growth boundaries

Home wood heating season October 1 to May 31; advisory line 541-746-4328; exemption only with an approved economic exemption letter · Checked 2026-10-02. LRAPA wood heating

Oregon DEQ adds that burning trash, treated wood or plastic in a home is illegal. Outdoor burning of branches and yard debris has its own rules: Washington yard debris burning rules and Oregon yard debris burning rules. This is a summary, not legal advice.

Questions people ask

How can you tell if firewood is seasoned?

Split a piece and test the fresh face with a moisture meter; below 20 percent is seasoned. Without a meter, look for wood that is darker and lighter than fresh wood and cracks sharply, rather than thuds, when two pieces are knocked together.

How long does Douglas fir take to season?

As a softwood, at least six months, by Washington Ecology’s guidance. Its low green moisture (35 percent of dry weight) helps: split in spring and stacked under cover, it can be ready by fall.

Does firewood dry over the winter in the Northwest?

West of the Cascades, winter is the season to keep wood dry, not to dry it: about three-quarters of Seattle’s and Portland’s yearly precipitation falls from October through March. OSU Extension’s advice is to season through a dry summer and keep the wood covered through the wet season.

Can you season firewood in a garage or shed?

The EPA’s advice is to store wood outdoors, off the ground, with only the top covered, because covered sides trap moisture. An open-sided woodshed fits that description; bring only a few days’ supply indoors.

Is kiln-dried firewood the same as heat-treated?

Not necessarily. Kiln-drying lowers moisture; heat treatment for pests means holding the wood core at a set temperature, 160°F for 60 minutes under Washington’s import rule, and the bag should say so.

Sources

  1. EPA Burn Wise, Best wood-burning practices (updated November 3, 2025), checked 2026-10-02.
  2. EPA Burn Wise, Test your wood with a moisture meter, checked 2026-10-02.
  3. EPA Burn Wise, Wet wood is a waste: moisture meter flyer (EPA-456/F-20-003), checked 2026-10-02.
  4. Oregon DEQ, Tips for cleaner burning, checked 2026-10-02.
  5. Washington Department of Ecology, Tips for outdoor burning and wood seasoning (April 11, 2025), checked 2026-10-02.
  6. Washington Department of Ecology, Wood stove information, checked 2026-10-02.
  7. Washington Department of Ecology, Burn bans, checked 2026-10-02.
  8. Washington Legislature, WAC 173-433-110, opacity standards for solid fuel burning devices, checked 2026-10-02.
  9. Washington Legislature, WAC 173-433-150, stage 1 and stage 2 burn ban restrictions, checked 2026-10-02.
  10. Multnomah County, Wood burning restrictions (updated October 1, 2026), checked 2026-10-02.
  11. Lane Regional Air Protection Agency, Wood burning (home wood heating advisories), checked 2026-10-02.
  12. OSU Extension, EC 1387, Burn dry firewood for safer, cleaner burning and efficiency, checked 2026-10-02.
  13. OSU Extension, EC 1628, Should I switch to firewood or wood pellets? (rev. 2013), checked 2026-10-02.
  14. OSU Extension, Ask Extension: How to prevent moisture in my firewood?, checked 2026-10-02.
  15. NOAA NCEI, U.S. Climate Normals 1991–2020 (monthly normals by station), checked 2026-10-02.
  16. NOAA NCEI, 1991–2020 monthly normals, Seattle-Tacoma International Airport (USW00024233), checked 2026-10-02.
  17. USDA Forest Service, Forest Inventory and Analysis, FIADB reference tables (REF_SPECIES green moisture), checked 2026-10-02.
  18. USDA Forest Products Laboratory, FPL-GTR-200, Heat treatment of firewood: meeting the phytosanitary requirements (2011), checked 2026-10-02.
  19. National Plant Board, Firewood heat treatment standards, checked 2026-10-02.
  20. Washington Legislature, chapter 16-476 WAC, firewood exterior quarantine (effective August 18, 2026), checked 2026-10-02.

Westcoast-Tree.org is an independent information site. If you call a number on this site, the call goes to a tree service that covers your area and we may be paid a referral fee by that company. We don't perform tree work and we don't vet, license or insure anyone. Cost figures are modeled estimates, not quotes (method). Not affiliated with the former Westcoast Tree Care Inc of Tumwater, WA.

Call for a local estimate(877) 720-7431